series AM10T-IZ 10 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.a 1 of 3 north america only features: ? short circuit & ovp protection ? ? 24 pin dip package ? ? wide 2:1 input range ? ? power modules for pcb mounting ? no minimum load ? models single output model input voltage (v) output voltage (v) output current max (ma) capacitive load, max(uf) ripple & noise max, (% mv p-p ) efficiency (%) am10t-1203siz 9-18 3.3 2000 4200 80 79 am10t-1205siz 9-18 5 2000 3200 80 75 am10t-1212siz 9-18 12 830 600 120 81 am10t-1215siz 9-18 15 660 390 150 81 am10t-2403siz 18-36 3.3 2000 4200 80 71 am10t-2405siz 18-36 5 2000 3200 80 78 am10t-2412siz 18-36 12 830 600 120 82 am10t-2415siz 18-36 15 660 390 150 83 am10t-4803siz 36-75 3.3 2000 4200 80 73 am10t-4805siz 36-75 5 2000 3200 80 82 am10t-4812siz 36-75 12 830 600 120 82 am10t-4815siz 36-75 15 660 390 150 83 models dual output model input voltage (v) output voltage (v) output current max (ma) capacitive load, max(uf) ripple & noise max, (%) efficiency (%) am10t-1205diz 9-18 5 1000 1800 80 75 am10t-1212diz 9-18 12 410 300 120 80 am10t-1215diz 9-18 15 330 200 150 80 am10t-2405diz 18-36 5 1000 1800 80 79 am10t-2412diz 18-36 12 410 300 120 82 am10t-2415diz 18-36 15 330 200 150 84 am10t-4805diz 36-75 5 1000 1800 80 77 am10t-4812diz 36-75 12 410 300 120 82 am10t-4815diz 36-75 15 330 200 150 83 input specifications parameters nominal typical maximum units voltage range 12 24 48 9-18 18-36 36-75 vdc filter capacitor absolute ma ximum rating 12 vin 24 vin 48 vin ?
series AM10T-IZ 10 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.a 2 of 3 north america only isolation specifications parameters conditions typical rated units tested i/o voltage 60 sec 1500 vdc resistance > 1000 mohm capacitance 470 pf output specifications parameters conditions typical maximum units voltage accuracy 2 % short circuit protection continuous short circuit restart auto recovery over voltage protection zener diode clamp >110% vdc over load protection auto recovery over 110% full load line voltage regulation hl-ll 0.5 % load voltage regulation (single) 0 ? 100% full load 0.5 % load voltage regulation (dual) 0 ? 100% full load 2 % temperature coefficient 0.05 %/ o c ripple & noise 3.3 & 5v models 12 & 15v models 80 mv p-p 1% vout p-p mv general specifications parameters conditions typical maximum units switching frequency 100% load 300 khz operating temperature derating above +50 o c -40 to +75 o c storage temperature -55 to +115 o c case temperature +95 o c cooling free air convection humidity 95 % case material nickel coated cooper weight 18 g dimensions (l x w x h) tolerance 0.02 inch, 0.5mm 1.25 x 0.80 x 0.40 inches 31.80 x 20.30 x 10.20 mm mtbf > 700 000 hrs (mil-hdbk -217f, ground benign, t=+25 o c) note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. safety specifications standards agency approvals ul (pending) safety en 55022, class a en 55024
series AM10T-IZ 10 watt | dc-dc converter www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 051e r12.a 3 of 3 north america only pin out specifications dimensions derating note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet. 7. warranty is in accordance with aimtec?s st andard terms of sale available at www.aimtec.com. pin single dual 2 -v input -v input 3 -v input -v input 9 n.c. common 10 omitted omitted 11 n.c. -v output 14 +v output + v output 15 omitted omitted 16 -v output common 22 +v input +v input 23 +v input +v input bottom view 22.80 (0.90) 20.30 (0.80) 2.50 (0.10) 5.00 (0.20) printed face 10.20 (0.40) 3.80 (0.15) 0.50 (0.02) 15.20 (0.60) 31.80 (1.25) 23 9 11 14 16 22 23 output power %
|
